歡迎來到中科聚峰機械有限公司·▩•◕·!

24小時服務熱線▩•·▩:

400-879-1999

點選撥打服務熱線▩•·▩:400-879-1999
當前位置▩•·▩:首頁>產品中心>平口攪拌車>3.5方平口攪拌車

3.5方平口攪拌車

來源▩•·▩:http://www.hzxdsc.com/ 日期▩•·▩:2021-03-22 釋出人▩•·▩:guanli
概述▩•·▩:3 5方平口攪拌車是用來運送混凝土的專用車輛│↟,這種車的後面會安裝一個大罐│↟,用來對混凝土進行攪拌的◕·。為大家介紹一下自動上料攪拌車的操作

3.5方平口攪拌車是用來運送混凝土的專用車輛│↟,這種車的後面會安裝一個大罐│↟,用來對混凝土進行攪拌的◕·。為大家介紹一下自動上料攪拌車的操作◕·。
4.0 square mouth mixer is a special vehicle for transporting concrete. A large tank will be installed at the back of the truck to mix the concrete. To introduce the operation of automatic feeding mixer.
一✘₪✘✘、人進入筒內清除混凝土的結塊時│↟,應將車輛熄火│↟,拔下電門鑰匙│↟,筒外設人監護◕·。
1✘₪✘✘、 When people enter the cylinder to remove the concrete caking, they should turn off the vehicle, pull out the switch key, and set people outside the cylinder to monitor.
二✘₪✘✘、操作操縱桿時│↟,應在“空檔”位置稍作停留後方可動至下一個位置◕·。
2✘₪✘✘、 When operating the control lever, stop at the "neutral" position for a while before moving to the next position.
三✘₪✘✘、運輸前│↟,卸料槽必須固定在“行駛”位置│↟,防止擺動◕·。
3✘₪✘✘、 Before transportation, the discharge chute must be fixed in the "driving" position to prevent swing.
四✘₪✘✘、啟動後│↟,應將攪拌操縱桿放在“卸料”位置│↟,放去筒內積水◕·。
4✘₪✘✘、 After starting, the mixing control rod should be placed in the "discharge" position to remove the water in the cylinder.
五✘₪✘✘、裝料時│↟,攪拌操作杆應放在“裝料”位置◕·。
5✘₪✘✘、 When loading, the mixing operating rod should be placed in the "loading" position.
六✘₪✘✘、啟動前│↟,應將攪拌操縱桿放在“空檔”位置◕·。
6✘₪✘✘、 Before starting, put the mixing control lever in the "neutral" position.
七✘₪✘✘、搞好文明施工│↟,桶內多餘材料不準隨便亂倒◕·。卸料後必須對攪拌筒✘₪✘✘、料槽✘₪✘✘、託輥等部位進行清洗◕·。
7✘₪✘✘、 Do a good job in civilized construction, and do not dump the surplus materials in the barrel. After discharging, the mixing drum, material trough, idler and other parts must be cleaned.
八✘₪✘✘、啟動前應對機械系統各部位認真進行檢查│↟,確認良好後方可啟動◕·。
8✘₪✘✘、 Before starting, all parts of the mechanical system should be carefully checked, and the machine can be started only after it is confirmed to be in good condition.
上一條▩•·▩: 2.6方平口攪拌車
下一條▩•·▩: 4方平口攪拌車

截圖│↟,微信識別二維碼